Table of Contents
- 1 Why is heat transfer coefficient value of natural convection much less?
- 2 What is the range of H for natural convection in gases and liquids?
- 3 What is the relationship between convective heat transfer coefficient of natural convection and forced convection?
- 4 What factors affect convection?
- 5 What is the reason for the high convective heat transfer coefficient?
- 6 What is the rate of convection from one side of plate?
- 7 What are the advantages and disadvantages of natural convection?
Why is heat transfer coefficient value of natural convection much less?
In general heat transfer coefficient in natural convection is far less compared to forced convection. In natural convection, the heat is taken away slowly by buoyancy force and in forced convection, the heat is taken away fastly by velocity.
What is H in convection heat transfer?
The convective heat transfer coefficient, h, can be defined as: The rate of heat transfer between a solid surface and a fluid per unit surface area per unit temperature difference. This is due to turbulent flow having a thinner stagnant fluid film layer on the heat transfer surface.
What is the range of H for natural convection in gases and liquids?
For natural convection, h is in the range of 5–15W·m−2·K−1 in gases and 50–100W·m−2·K−1 in liquids. For forced convection, h values would reach 15–250W·m−2·K−1 in gases and of 100–2000W·m−2·K−1 in liquids.
What does natural convection depend on?
Natural convection on a surface depends on the geometry of the surface as well as its orientation. It also depends on the variation of temperature on the surface and the thermophysical properties of the fluid.
What is the relationship between convective heat transfer coefficient of natural convection and forced convection?
In forced convection, the fluid is in motion produced by a pump or a fan….14.3. 1.2 Thermal convection.
| Type of Convection | Convective Heat Transfer Coefficient, h | |
|---|---|---|
| Btu / ( h×ft 2 ×R ) | W / ( m 2 ×K ) | |
| Air, free convection | 1–5 | 2.5–25 |
| Air, forced convection | 2–100 | 10–500 |
| Liquids, forced convection | 20–3000 | 100–15,000 |
What is the effect of convective heat transfer coefficient h’on fin effectiveness?
The higher value of h causes the smaller efficiency and effectivity of the fin. Sahin and Demir, 2008 found that heat transfer coefficient (h) affect to the fin’s performance. This is because the temperature distribution generated on the fin has a closer temperature with the fluid around the fin [5].
What factors affect convection?
Spontaneous convection is driven by buoyancy for the most part and surface tension to a lesser extent.
- exposed surface area.
- viscosity.
- density.
- conductivity (when conductivity is high, there is no need for convection)
- acceleration due to gravity.
What is natural convection give example?
Examples of natural convection are oceanic winds. Forced convection: When external sources such as fans and pumps are used for creating induced convection, it is known as forced convection. Examples of forced convection are using water heaters or geysers for instant heating of water and using a fan on a hot summer day.
What is the reason for the high convective heat transfer coefficient?
For turbulent flow, the heat transfer coefficient increases with increasing mass flux (or Reynolds number). This is because higher velocity increases turbulence, which in turn provides a more efficient radial transport/mixing of heat.
What is the typical value of convective heat transfer coefficient?
Typical Values of the Convective Heat Transfer Coefficient A new computer chip with a surface area of 1.00 cm 2 generates 10.0 watts of heat. Determine the convective heat transfer coefficient needed to keep the temperature of the chip less than 20.0 °C above the environmental temperature.
What is the rate of convection from one side of plate?
For a flat plate at a uniform temperature T, the rate of heat flow (in Watts) due to convection from one side of the plate is: h⋅ A⋅ ΔT h W/(K⋅m2) convective surface conductance A m2 area of one side of plate ΔT K T− Tenv T K plate temperature Tenv K fluid temperature
What is the difference between heat transfer through fluid and convention?
Heat transfer through fluid is know as convention. There is mathematical function due to which natural and forced convention have different different value of h ( convective heat coefficient).In forced convention, It depends upon 7 parameters out of which 4 parameters are thermophysical property of fluid.
What are the advantages and disadvantages of natural convection?
An obvious advantage of natural convection, or “free” convection as it is sometimes called, is that the expense of incorporating a fan is avoided. Of course the penalty associated with this method of cooling is lower heat transfer coefficients.