How many amps is a 50 gallon water heater?

18.75 amps
A typical 50 gallon electric water heater runs at 4500 watts. In an electric circuit of 240 volts, 4500 watts is equivalent to 18.75 amps.

How many amps does a 40-gallon water heater?

An average 40-gallon electric water heater runs at 240 volts and a wattage of 2500 W. Hence, calculating the amperage 2500/240, we can deduce the amperage is 18.75 A.

How many amps is a 220 hot water heater?

The standard amperage for an electric water heater is 18.8 Amps with 240Volts, 4500 Watt.

What size breaker do I need for a 50 gallon water heater?

The standard for water heater circuits is #10, two conductors with ground (10/2) and a 30 amp circuit breaker for a water heater. If you are running cable anyway, just run #10 and replace the breaker so it’s done right, once and for all.

Can I use a 40 amp breaker for water heater?

In general, NO. Doing so is very dangerous and could start a fire! 10 gauge wire requires at most a 30A breaker, whereas 8 gauge requires at most a 40A breaker.

What size breaker do I need for my water heater?

Multiply the value for current by 125 percent to determine the size of the breaker you need for the heater. A 1500-watt heater on a 120-volt circuit thus needs a breaker of 15.6 amps. Because a 15-amp breaker would be too small, you need a breaker with the next highest rating, which is 20 amps.

Can I use a 40 amp breaker for a water heater?

What size breaker do I need for a water heater?

Electric water heaters require a dedicated 240-volt dedicated 30-amp circuit and a 10-2 non-metallic (NM) or MC cable. This means the breaker only powers the water heater and no other appliances. A 30-amp circuit breaker can power all 4500watt water heaters regardless of gallon size.

Can I use a 40 amp breaker for a 30-amp water heater?

You just swap out a 30A breaker with a 40A breaker. You’re allowing the electrical system (not just the breaker) to run at 33\% over it’s rated capacity.

Can I use 10 3 wire for a hot water heater?

Can I Use 10 3 Wire For A Hot Water Heater? You can use 10/3 wire. Use the red and black wires as hot conductors. The ground wire will run to the green screw.

How many amps does a 240-volt water heater use?

18.8 amps
Most electric water heaters use 18.8 amps with 240 volts and a 4,500 watt heating element. A gas water heater uses less amps—about 12 Amps with 115 volts. The average residential container heater has a 40-gallon tank and usually requires a 30-amp breaker.

Can you use 30 amp breaker 40 amp water heater?

What is the average wattage of a water heater?

The wattage on hot water heater elements can range from 1500 to 5500 watts. Wattage is determined by voltage so you want to match the voltage and wattage for your new elements. The best place to find the wattage and voltage information is on the label that is attached to the side.

The 125\% calculation only applies to continuous loads.

How many amps does a tankless water heater draw?

The size of your breaker box and how many amps you have available is the most important thing to consider when purchasing an electric water heater. Depending on which electric tankless water heater best fits your home needs, the required amps will be 150 or 200 amps.

What are the requirements for electric water heater?

Electric water heaters require a 240-volt dedicated circuit, which serves only the water heater and no other appliances or devices. The circuit wiring typically includes a 30-amp double-pole breaker and 10-2 non-metallic (NM) or MC cable.