Table of Contents
What is modification factor in slab design?
For obtaining modification factor, the percentage of steel for slab can be assumed from 0.2 to 0.5\%. The effective depth d of two way slabs can also be assumed using cl.
What is the role of modification factor for tension reinforcement?
Modification factor for tension reinforcement To allow for the effects of the amount of tension reinforcement (effect of ultimate flexural capacity of the beam – increasing flexural rigidity of beam) and the service stress (effect of utilization of the design flexural capacity – implying a lower moment at SLS), the …
What are the conditions to be followed in design of slab?
What are the Design Requirements of Concrete Slab Design-Deign of…
- Effective Span for concrete slab design.
- 2.Limiting Stiffness.
- 3.Minimum Reinforcement for concrete slab design.
- Maximum diameter of bars.
- 5.Spacing of main reinforcement.
- Distribution reinforcement for concrete slab design.
- Cover to reinforcement.
How do you check for deflection in slab design?
Checking slab deflection is included in the beam design section of BS 8110 Part 01. The deflection can be checked by two methods. If you know the maximum deflection for the relevant load case, we can check whether it is with in the limit. Code gives the maximum limits of deflections base on the spans.
What is a modification factor?
Modification Factor (The “Mod”) — the factor by which a standard workers compensation premium is multiplied to reflect an insured’s actual loss experience.
What is clear span of slab?
The distance between the centers of support, or the clear distance between supports plus the effective depth of the beam or slab, the lesser value being taken.
What is one-way slab in civil engineering?
The one-way slab is a slab, which is supported by parallel walls or beams, and whose length to breadth ratio is equal to or greater than two and it bends in only one direction (spanning direction) while it is transferring the loads to the two supporting walls or beams, because of its geometry.
What is K in slab design?
The floor slab (PANEL 1) is spanning in two directions, since the ratio (k) of the longer side (ly) to the shorter side (lx) is less than 2.
What is RB work?
REINFORCED BRICKWORK (R.B. WORK) MATERIALS. CENTERING AND SHUTTERING. MIXING OF MORTAR. LAYING.
How do you ensure slab against deflection?
Construction Measures to Reduce Deflection Slabs
- Cure the concrete to decrease creep and shrinkage.
- Build camber into the floor slab.
- Materials Selection to Reduce Deflection of Beams and Slabs.
- Use concrete with a higher modulus of rupture.
- Use fibers to the concrete mixture.
- Cure the concrete to allow it achieve strength.
What is slab deflection?
Published May 20, 2021. + Follow. Long-term deflection in slabs is the deflection or deformation that occurs over time due to shrinkage and temperature. It is also influenced by the condition of the cracking and concrete creep. Long-term deflection is very important in the design of reinforced concrete structures.
How to calculate modification factor of steel for slab?
For obtaining modification factor, the percentage of steel for slab can be assumed from 0.2 to 0.5\%. The effective depth d of two way slabs can also be assumed using cl.24.1,IS 456 provided short span is <3.5m and loading class is <3.5KN/m 2 One way slab d= (L/22) to (L/28).
What are the design guidelines for rereinforced concrete slab?
Reinforced Concrete Slab Design Guidelines a) Effective span of slab: Effective span of slab shall be lesser of the two L = clear span + d (effective depth) L = Center to center distance between the support; b) Depth of slab: The depth of slab depends on bending moment and deflection criterion. the trail depth can be obtained using:
How do you calculate the depth of a slab?
The depth of slab depends on bending moment and deflection criterion. the trail depth can be obtained using: Effective depth d= Span / ((L/d) Basic x modification factor) For obtaining modification factor, the percentage of steel for slab can be assumed from 0.2 to 0.5\%.
What is the design of a slab?
Design of slab is based on deflection. Designed based on failure by deflection. The length of slab is limited to ensure the deflection is within the limit However the above values can be modified with percentage of steel, because when we add steel the deflection will change.
https://www.youtube.com/watch?v=ny7VEAuwM3s